HP certification

pass4side has assembled to take you through 120 Q&As to your HP0-238 Exam preparation. In the HP0-238 exam resources, you will cover every field and category in HP0-238 helping to ready you for your successful Juniper Certification.

Quality and Value for the HP0-238 Exam

pass4side Practice Exams for HP HP0-238 are written to the highest standards of technical accuracy, using only certified subject matter experts and published authors for development.

100% Guarantee to Pass Your HP0-238 Exam

If you prepare for the exam using our pass4side testing engine, we guarantee your success in the first attempt. If you do not pass the Certification I HP0-238 exam (Supporting the MSA1000 and SCSI JBODS) on your first attempt we will give you a FULL REFUND of your purchasing fee AND send you another same value product for free.

HP HP0-238 Downloadable, Printable Exams (in PDF format)

Our Exam HP0-238 Preparation Material provides you everything you will need to take your HP0-238 Exam. The HP0-238 Exam details are researched and produced by Professional Certification Experts who are constantly using industry experience to produce precise, and logical. You may get questions from different web sites or books, but logic is the key. Our Product will help you not only pass in the first try, but also save your valuable time.

　
　
Exam : HP HP0-238
Title : Supporting the MSA1000 and SCSI JBODS


1. What is the recommended action to take when a controller fails in a redundant MSA1000 configuration?
A. Power off the MSA1000 and replace the failed controller.
B. Replace the failed controller online.
C. Push the right arrow push button on the front panel to failover the controller and replace the failed controller.
D. Modify the zoning so that the MSA1000 is not accessible during the online replacement of the failed controller.
Answer: B

2. Click the Exhibit button.
Which LED on the MSA1000 controller indicates a failure on a configured hard disk?
A. LED 9
B. LED 15
C. LED 16
D. LED 17
Answer: B

3. You are assigning DISK109 as a spare drive to array B containing logical drives 2 and 3. What is the correct CLI (command line interface) command?
A. ADD SPARE UNIT=2 DISK109
B. ADD SPARE ARRAY B DISK109
C. SET SPARE ARRAY B DISK109
D. SET SPARE UNIT 3 DISK109
Answer: A

4. Click the Exhibit button.
The EMU in a MSA1000 has detected a temperature problem. Which LED of the enclosure status indicators reports the problem and how does the LED display the error condition?
A. LED 1 is off.
B. LED 2 is amber.
C. LED 3 is off.
D. LED 3 is amber.
Answer: D

5. The customer has a single controller MSA1000 configuration. What is the recommended action to replace the failed controller?
A. Power down the MSA1000. Remove the failed controller and install the old cache module in the replacement controller.
B. Push the right arrow push button on the front panel to clear the cache of the controller and replace the failed controller.
C. Replace the failed controller online, with a new cache installed.
D. Push the left arrow push button on the front panel to clear the cache of the controller and replace the failed controller.
Answer: A

6. The MSA1000 controller display module can hold up to 100 messages. Once the maximum is reached, the older messages will be ____.
A. copied to the connected host using ACU-XE
B. copied to the connected host using the serial line
C. deleted
D. copied to the connected metadata part of the disks
Answer: C

7. Click the Exhibit button.
On an MSA1000 disk, LEDs 1 and 2 are OFF, and LED 3 is ON. What is the possible cause for the status and which action should you take?.
A. The drive is part of the selection of the array configuration utility. Do not remove this drive without verifying the configuration.
B. The array is rebuilding. Do not remove this drive without verifying the configuration.
C. The array is performing an online expansion. Do not remove this drive without verifying the configuration.
D. The drive failed and has been taken offline. You can remove the drive.
Answer: D

8. Click the Exhibit button.
Which LED on the MSA1000 controller indicates an error message was sent to the controller display?
A. LED 9
B. LED 15
C. LED 16
D. LED 17
Answer: D

HP0-238 Downloadable, Interactive Testing engines

We are all well aware that a major problem in the IT industry is that there is a lack of quality study materials. Our Exam Preparation Material provides you everything you will need to take a certification examination. Like actual certification exams, our Practice Tests are in multiple-choice (MCQs)

Our HP Certification I HP0-238 Exam will provide you with exam questions with verified answers that reflect the actual exam. These questions and answers provide you with the experience of taking the actual test. High quality and Value for the HP0-238 Exam:100% Guarantee to Pass Your Certification I exam and get your Certification I Certification.