EMC Certification

pass4side has assembled to take you through 120 Q&As to your E20-331 Exam preparation. In the E20-331 exam resources, you will cover every field and category in E20-331 helping to ready you for your successful Juniper Certification.

Quality and Value for the E20-331 Exam

pass4side Practice Exams for EMC E20-331 are written to the highest standards of technical accuracy, using only certified subject matter experts and published authors for development.

100% Guarantee to Pass Your E20-331 Exam

If you prepare for the exam using our pass4side testing engine, we guarantee your success in the first attempt. If you do not pass the EMC Certification E20-331 exam (Symmetrix Business Continuity Implementation Exam for I.E.s) on your first attempt we will give you a FULL REFUND of your purchasing fee AND send you another same value product for free.

EMC E20-331 Downloadable, Printable Exams (in PDF format)

Our Exam E20-331 Preparation Material provides you everything you will need to take your E20-331 Exam. The E20-331 Exam details are researched and produced by Professional Certification Experts who are constantly using industry experience to produce precise, and logical. You may get questions from different web sites or books, but logic is the key. Our Product will help you not only pass in the first try, but also save your valuable time.

　
　
Exam : EMC E20-331
Title : Symmetrix Business Continuity Implementation Exam for I.E.s


1. Click on the Exhibit button.
A disaster has occurred at the Workload Site of a SRDF/Star triangle. What is the first SRDF/Star action that must be performed to allow production to start at the Synchronous Target Site?
A.connect
B.enable
C.protect
D.switch
Answer: D

2. In a Single Hop SRDF/AR setup the following options have been set:
The symreplicate session was started at time 0. The actual cycle time was 450 seconds. How many seconds after the start of the first cycle will the next cycle start?
A.300
B.450
C.600
D.900
Answer: C

3. Which two TimeFinder/Clone actions are initiated when issuing a symclone establish command?
A.Activate and Restore
B.Create and Activate
C.Create and Terminate
D.Re-create and Terminate
Answer: B

4. In which operating system will disk numbering be changed with a dynamic 'createpair' operation?
A.AIX
B.HP-UX
C.Linux
D.Windows
Answer: A

5. A UNIX server has 4 HBAs. Each HBA is zoned to a different FA port on a DMX1000. Each HBA has access to the same 20 Symmetrix Devices. PowerPath has been installed and configured on the UNIX Server.
Applications A & B have each been assigned 10 devices. Performance is extremely important for Application A, while availability is critical for both applications.
Which PowerPath configuration will meet the requirements?
A.Set the load balacing policy for all devices for both applications to Least I/O
B.Set the load balancing policy of all paths of Application B to Symmetrix Optimization
C.Set the mode for 2 of the paths of Application B to Standby and the other 2 to Active
D.Set the mode for all paths of Application B to Standby and all paths of Applicaton A to Active
Answer: C

6. In order for an R2 device to act as a control device for Open Replicator hot push, what is the valid state for a synchronous R1 and R2 pair?
A.Consistent
B.Failed Over
C.Synchronized
D.SyncInProgress
Answer: B

7. Click on the Exhibit button.
<Missing>
A disaster at the source Symmetrix site caused an SRDF/A Multi-session consistency group (MSC group) to stop propagating host writes to the target site. At the time of the disaster one of the target arrays had a complete Receive Delta set and the other one had an incomplete Receive Delta set.
Which action must be performed on the target site data to ensure dependent write consistency?
A.Consistent split
B.Database recovery
C.Enable consistency
D.MSC cleanup
Answer: D

8. Click on the Exhibit button.
Which Open Replicator operations can be performed between the DMX and third-party array with the architecture displayed?
A.Cold Push and Cold Pull only
B.Cold Push and Hot Push only
C.Cold Push, Cold Pull, Hot Push and Hot Pull
D.Hot Push and Hot Pull only
Answer: A

E20-331 Downloadable, Interactive Testing engines

We are all well aware that a major problem in the IT industry is that there is a lack of quality study materials. Our Exam Preparation Material provides you everything you will need to take a certification examination. Like actual certification exams, our Practice Tests are in multiple-choice (MCQs)

Our EMC EMC Certification E20-331 Exam will provide you with exam questions with verified answers that reflect the actual exam. These questions and answers provide you with the experience of taking the actual test. High quality and Value for the E20-331 Exam:100% Guarantee to Pass Your EMC Certification exam and get your EMC Certification Certification.